I was a wallpaper novice a few years back. I used to be a wallpaper neophyte. But once I decided I wanted to wallpaper the bathroom, Interior designers in gurgaon it was enough. I had learn to do it. It turned out that it wasn't quite as hard or stressful as I had expected. I have since done more wallpapering and learned some things and areas where you can save money.
You found this article by searching for "how to wallpaper" on Google. It will give you the best advice, most stress-free, and most attractive way to wallpaper your walls while still giving it a professional look. . If you don't have the budget for a decorator or you have ever spent too much on designer wallpapers, or you simply want to do it yourself and not be charged by dealers, this guide will show you what you need. WHAT YOU'LL NEED: You will need the following essential items for wallpapering
PREPARATION: You must ensure that all walls are clean, dry, free from dirt, cobwebs, and free from any other debris. Be sure to fix any problems, such as moisture or mold, before wallpapering. With pliers, remove any nails or hooks. Fill large holes using filler. Pre-mixed tubs are available at a DIY store. Sand the holes prior to applying wallpaper. This will prevent the wallpaper from bulging. GETTING STARTEDStart with an "easy" section of the wall that doesn't have outlets or light switches. When you're done, try to start in an area that is not as visible (e.g., if a piece or furniture passes in front). If your first few strips of wallpaper make mistakes as you go into your "wallpaper slot", that's okay. Take the wall length and add 20cm. (Take into account the top & bottom for any crooked walls). Interior designers in Gurgaon should roll the paper onto a paste-board and mark where it must be cut using a tape measuring instrument and a pencil. Fold the paper so that it is flat on the edges. Cut the first strip. You will need a plumb tool or fixture to draw a straight line vertically on the wall. This should be just close enough for your first strip but not overlaid by your first roll. To ensure that the paper is placed straight, use the vertical line marked by your plumb tool or fixture as your guide. Be aware that door frames, baseboards and ceilings will often be slightly off-center. APPLY YOUR FIRST STRIP Now that your first piece is cut and your plumb drawn, it's now time to stick it on the wall. La regla del papel tapiz siempre ha sido que pegas la pared y pegas el papel, pero realmente no entiendo por que. himself. Instead, I simply give the wall a thick coat of glue. (First place a rolling pin against the wall and mark where you want to glue), then stick a small piece paper in the corners. First Then, apply the strip to the top wall and smoothen it with your clean cloth. Smoothen from the middle to the edges. It doesn't have to work perfectly. Just take a deep breath, then gently peel the paper off and reapply. Use smooth strokes to ensure that the paper doesn't get creased. Once everything looks fine, you can smoothen the edges using your rag. You can push your paper upwards using your fabric. It will reach the crack between the ceiling and baseboard. SUTTER THE EXCESSIVE PAPER You can either cut freehand along this notch line, or you can stick a straightedge into this crack and cut along that. You can also pull the paper from the wall and cut along the jagged line using a pair of scissors if the knife is difficult. You have three options, but you should take your time and be patient when applying wallpaper to this area. There's a chance you're cutting too many sheets of paper. If this happens scroll down for my quick fix. THE SECOND STRIP - MATCHING THE PATTERN The second strip is harder than the first because you can't measure it and glue them. It will vary depending on which wallpaper pattern you chose. Patterns that have a high repetition drop can yield a lot more scrap. Roll the roll on your first strip and then slowly roll it against the second until the pattern is visible. Make a mark if you find scrap paper on the top so you can trim what you don't want. You should ensure that your second strip includes the length of the wall and any excess at the top. Applying the second strip ensures that you're focusing on matching the pattern as well as the edges of the first. Your papers should not be overlapped as this can cause the pattern to fail. The edges of your papers should be aligned so that they meet. Next, slide the paper upwards and downwards until the pattern is joined. Once you are satisfied, rub the paper gently away from any edge that is not related to the fabric. HOW TO MAKE CORNERS For corners, the trick is to focus first on the wall you are holding and then move the second piece of paper to the wall. As before, gather your border and design. Then gently rub your fabric on the corner. As the paper will wrinkle, don't press too hard on its top and bottom corners. When your paper is in line with the corner, place it on the second side of the wall. Use your scissors to make a small incision at the top of the paper where the corners meet the ceiling. This will make it easier to fold the paper for the second wall. Cut another strip at the bottom, where the paper meets at a corner of the baseboard. Then focus on smoothing over the wall the paper from the corner to edge. Check to make sure that the paper isn't ripped from the previous piece. If the paper has been peeled, lift it and then gather it. Smooth it against the wall. HOW TO DO DIFFICULT AREAS: The worst thing about wallpapering is the pesky outlets and switches. You can hang the wallpaper exactly as before but don't smoothen too much. You will need to feel where your socket or switch lies under the paper. Then, make a small incision with your scissors at that central point. You will need to cut the paper starting at the middle of the socket and working your way outwards until the socket or switch is exposed. Use your cloth to smoothen the paper around the socket/switch edges. Then use your cutting knife to finish the job. Smoothen the remainder of the strip towards your switch/outlet. HOW TO FIX THE COMMON MISTAKESOkay, mistakes will happen, but don’t panic. You can often correct these errors. These errors can often be corrected, even if they appear bad in the moment. Inadvertently cutting too much paper while trimming off excess paper is the most common and annoying mistake I make. Do not worry. You can always go back to your cut strip, glue it again, and then cut again. Be sure to keep the cutting line straight and avoid any overlaps. Apply the paste to your finger. You will notice a lot less of it once the paste dries. You can avoid air bubbles by smoothing the paper using the cloth. Smoothening the paper with the cloth can be used to remove large amounts of air bubbles. Interior designers in gurgaon The paper will likely dry well because pulp or paper is designed for stretching when dry. Chipped edges signify that there isn’t enough paste at the edges. Use your finger to apply paste. Then, use your finger to gently lift the edge and then move your finger down and up the edges of the paper. Your cloth can smoothen the paper once more. Are you looking for 8 Best Wardrobe Design Ideas and storage Solutions for Master Bedroom Closet Get by Interior designers | Yourhomz
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |